The problem is quite simple to find. You have to make some measurements on the LF347 (Op AMP) with the computer running and without sound.

You have to measuring pin 1 and pin 7 and should have a voltage of about 2.5V if the voltage as in my case is of 11.30v and 11.37v. Something is not working.

After replacing the LF347 with a LM324 or better a TL084 the right voltages are back and the sound works again.

Gallery of the repair:

*UPDATE*

After a couple of days, i have realized that the Amiga 600 still had some problems with the sound, although subtle but annoying and after a few measurements i have concluded that the LM324 is not fully compatible and cannot replace the LF324 (at least on the Amiga 600/1200).

After removing the LM324 and replaced with a TL084 everything has started to work much better than before.

I have done an accurate cleaning of the leaked battery acid on the mainboard.

I have also replaced the GARY socket destroyed by battery acid and rebuild a pcb track with a wire.

Gallery of the repair:

The problem of the green screen of death is usually due to a problem of DRAM,FAT AGNUS (chip or socket), GARY.

In this case all four DRAMs are failed. The pin 18 (IO/3) was always at high level.

Replacing DRAM everything has started to work properly.

Gallery of the repair:

We begin to explain what is this PHA-2037. This interface/Converter for the Home Computer Texas Instruments TI-99/4a is used to convert the video signals from Component (Y/Pb/Pr) to RGB (Scart Standard).

The defect of the PHA-2037 that i have received for repairing is to display images without the “BLUE” color in this case of the Video Component “Pb”.

The problem was in one of the three LM 318 (Op Amp). Just replaced, the PHA-2037 has begun to work properly.

PS: How you can see from a photo a pin of a transistor has not been cut. Maybe it was better to do it. :D

Gallery of the repair:

Brief summary of NOT repairing the Commodore Chessmate of a dear friend (Giacomo Vernoni).

The Chessmate I received had a funny defect: it worked for 10-15 seconds and then freezed completely with harrowing sounds in the background. So the defect appeared when something warmed up.

Having another Chessmate (mine) to compare the signals to, I noted right away that communication was missing between RIOT (6530) -> ROM (6332) -> CPU (6504) -> RAM (AM9111); CLOCK and RESET were working fine.

I sprayed synthetic ice on the 6530 RIOT to check if the problem was caused by this IC: as a matter of fact, after lowering its temperature, the Chessmate began to work again. I was glad I found the problem, but quite unhappy because the spare part is almost impossible to find. To double check I decided to unsolder the 6530, install a socket, and try it on my Chessmate.

It worked! Damn… after thinking about it for a while, I thought that maybe the spray partially freezed the nearby ROM too.

So I reinstalled the 6530 back in the non-working Chessmate, I turned it on, and after 15 seconds I sprayed the synthetic ice on the 6332, and it magically worked again.

That’s it… from that moment on, the Chessmate always worked! after the freezeing spray I left the Chessmate turned on for two hours and it never stopped working.

So, I’m asking myself: did the ice repair the ROM? Will it die again? probably yes :-D Maybe there was some small tin residue on the PCB that I removed by spraying it: I noticed that the Chessmate had already been repaired before, there were visible signs on the pcb.

It will remain a mystery, anyway the MPS 6322 ROM can be replaced by a 2532 EPROM (pinout compatible) or by a 2732 EPROM with an adapter.

Gallery:

Regeneration of the Keyboard PAD.

Some keys did not work properly. The Keyboard PAD have been regenerated using a suitable product that can be found for sale on eBay. Try: KEYPAD FIX

Gallery of the fix:

The Commodore 2031 and Commodore 4031 are single-unit 5¼” floppy disk drives for Commodore International computers. They use a similar steel case form to the Commodore 9060/9090 hard disk drives, and use the IEEE-488 interface common to Commodore PET/CBM computers. Essentially, both models are a single-drive version of the Commodore 4040.

The Commodore 2031LP is functionally the same as the 2031, but used the lower-profile tan case of the second version of the Commodore 1541 floppy disk drive intended for home computer use.

These drive models use a single-density, single-side floppy data storage format similar to that used by the Commodore 1540 & Commodore 1541 drives, but with a slightly different data marker indicating which model originally formatted the disk. The low-level disk format is similar enough to allow reading between models, but different enough that one series of drive models cannot reliably write to disks formatted with one of the other model series. A different of one extra ‘header’ byte is what causes this write incompatibility.

Gallery:

Comparison Commodore Floppy Drive 2031 (Low Profile) & 2031 (High Profile):

Fix the Commodore Floppy Drive 2031 (High Profile)

Removed the filter capacitors RIFA in the power plug.

Download: Commodore Floppy Drive 2031LP/HP Rom (1132)

source: wikipedia

There is nothing simpler than burning the Kickstart ROM at home :D

Gallery:

Below you can download the Amiga Kickstart 3.1 rom already ready for programming, the only thing that you have to do is the “Byte Swap” with your programming EPROM software.

Download: Amiga 500/600/1200/2000/4000 Kickstart 3.1 ROM + Docs (688)

NOTE: Download REMOVED (DMCA infringement)

Replacing electrolytic capacitors Commodore Amiga 600/1200.

Gallery full Recap 2 x Commodore Amiga 1200:

Gallery full Recap 1 x Commodore Amiga 600:

All computers that i use for experiments or tests must at least be cleaned and disinfected.

Works that have been made:

• General and accurate cleaning.
• Accurate cleaning with a magnifying lens of the AMIGA logo with isopropyl alcohol. I have used also a toothpick to remove the black color from the corners.
• Full Recap of the motherboards.
• Removed the two pieces of metal.
• Fixed the RGB video connector (totally broken).
• Replaced the keyboard with another one less yellowed.
• Added a Gotek Floppy Drive with HXC Firmware.
• Kickstart ROM 3.1.

Photo gallery before cleaning:

Photo gallery after cleaning:

Repair Motherboard (ASSY 326298) Drean Commodore 64

Defect:

• Black Screen.
• Missing Video Signal.

Cause of the Missing Video Signal:

• The motherboard of this C64 to work with the PAL-N video (Argentina) has been modified. Some pcb tracks are cut off and the modulator has been replaced. There are also a few bridges to retrieve the S-VIDEO output (luma / chroma).

Video Restoration:

• I have made a bridge with a wire for recover the composite signal that has been removed (tiny blue wire).

Repair:

• The cause of the black screen are 2 x MK 4564 ram in short circuit.

Photo gallery of repair:

The Commodore 2031 and Commodore 4031 are single-unit 5¼” floppy disk drives for Commodore International computers. They use a similar steel case form to the Commodore 9060/9090 hard disk drives, and use the IEEE-488 interface common to Commodore PET/CBM computers. Essentially, both models are a single-drive version of the Commodore 4040.

The Commodore 2031LP is functionally the same as the 2031, but used the lower-profile tan case of the second version of the Commodore 1541 floppy disk drive intended for home computer use.

These drive models use a single-density, single-side floppy data storage format similar to that used by the Commodore 1540 & Commodore 1541 drives, but with a slightly different data marker indicating which model originally formatted the disk. The low-level disk format is similar enough to allow reading between models, but different enough that one series of drive models cannot reliably write to disks formatted with one of the other model series. A different of one extra ‘header’ byte is what causes this write incompatibility.

Gallery:

Repair/Restoration Commodore Floppy Drive 2031LP

Defect:

• Lock lever of the Floppy Drive broken.
• When the Floppy Drive is powered up, red LED stays on and spindle motor runs continuously.

Repair/Restoration:

• Replaced the Lock lever with a new one taken from a Commodore Floppy Drive 1541 (spare parts)
• Replaced the ROM (UAB5 901484-05) with a EPROM MCM 68766 supplied from my friend Giacomo Vernoni.

Note:

The Eprom programming was done with a EPROM programmer Promenade by Jason-Ranheim Co. for Commodore 64.

Repair/Restoration Gallery:

Download: Commodore Floppy Drive 2031LP/HP Rom (1132)

source: wikipedia

The Home Computer Asem AM 100 is a clone of the Apple II+ (Apple // Plus). This computer was manufactured and assembled by ASEM S.p.A. Artegna (UD) / Italy.

The AM 100 is fully compatible with all the software available for the Apple II and II+. I have personally tested many programs and i’ve never found problems of compatibility.

Unfortunately this computer is arrived faulty, the repair was more simple than i expected, thanks to the IC sockets located on the computer motherboard.

Works that have been made:

• Replacing IC 74LS161 which shows a vertical band on the screen.
• Removing RIFA filter capacitor located inside the PSU.
• Regeneration of the Keyboard PAD. Some keys did not work properly. The Keyboard PAD have been regenerated using a suitable product that can be found for sale on eBay. Try: KEYPAD FIX
• General cleaning of the case outside/inside, monitor and keyboard.
• EPROM dump.

All these works are documented with photos that you can find below.

Gallery repairs:

12►

Under the cover gallery:

12►

Final photos:

Interesting discovery:

Inside the Floppy Drive reader (Apple clone) i have found the same mechanics (Mistumi / Newtronics) of the Commodore Floppy Drive 1541. See the first three pictures of the gallery: Under the cover.

Download: ASEM AM 100 full Eprom Dump (1142)

Jean-François DEL NERO (who’s behind the HxC SD Floppy Emulator) recently has released a version of the HxC emulator firmware that is compatible with the STM32 chip used in the Gotek floppy emulators.

This means that the great functionality of the HxC SD emulator is now available on cheaper and more widely available hardware.

The bootloader to convert the Gotek floppy drive in HxC compatible must be purchased on the website HXC 2001 by sending an email to Jean-François DEL NERO. The price of the bootloader is one-off 10 Euro per Gotek that you want to update. Future updates of the software are free and can be made from a USB stick

The HXC Usb (Gotek) firmware supports:

Flashing the Gotek floppy emulator with HxC firmware:

source: hxc2001.com

Replacing electrolytic capacitors Commodore Amiga 1200.

As you can see from the photos, the latest motherboard (Gallery full Recap Amiga 1200 #3) of Amiga 1200 suffered the classic problem of leaking capacitors.

Gallery full Recap Amiga 1200 #1:

Gallery full Recap Amiga 1200 #2:

Gallery full Recap Amiga 1200 #3: