SDI 2.1 KEYS	[16.11.2012 22:54]
-------------------------------------------------------------------------------
All parameters you change and values you enter are hexidecimal.
Input keys: 0123456789ABCDEF


OVERALL KEYBOARD COMMANDS for SEQUENCER, TRACKER & SOUND EDITOR:
-------------------------------------------------------------------------------
CBM 1-4         Track on/off
<-              Fast forward
F1              Play from mark
F2              Set play mark
F3              Stop/Continue play
F6              Tracker data on/off
F7/F8           Select octave (individual octaves for each track)
=               Play current line
Z               Play song from current line
RunStop         Sound Editor (Press again to exit)
/               Toggle Sequencer/Tracker & Sound editor.
SH L            Load music
CBM S           Dump music
CBM +/-         Next/Previous song
?               Set speed calls
CBM Q           Quantize (0/2) for recording notes
CRSR            Left/Right/Up/Down


KEYBOARD COMMANDS FOR SEQUENCER AND TRACKER:
-------------------------------------------------------------------------------
F5              Tracker/Sequencer
CBM *           Set speed voice (place cursor on track)
S/L             Tab jump left/right
SH ClrHome      To start of song
SH S            Save Music
SH A            Increase cursor jump
CBM A           Decrease cursor jump
V               View player counters/Full screen sequencer
SH C            Copy sequence
SH V            Paste into sequence 
SH D            Double sequence length
CBM F           Clear sequence (From cursor position)
CBM K           Kill sequence/Unused/Make a sequence ready for use.
M               Set start mark (grey background is marked area)
SH M            Set end mark
CBM M           Copy marked area to cursor position
:/[             Set track transpose
;/]             Set sequence number
H               Hunt and insert next unused sequence


KEYBOARD COMMANDS IN SEQUENCER:
-------------------------------------------------------------------------------
F4              Edit/Synth/Record mode
InstDel         Delete a line
SH InstDel      Insert a line
ClrHome         Cycle Sequence Top/Middle/Bottom
Space           Delete down
SH Space        Delete up
SH X            Narrow sequence (remove very 2nd line from cursor pos.)
CBM X           Expand sequnce (note: from cursor pos. place cursor on odd line for normality.)
CBM RTYU        Set track (channel) mark 
CBM 5678        Jump to track (channel) mark
,/.             Jump down/up 16 lines
>/<             Increase/Decrease note values (From cursor position)
Return          Start playing music from top of current sequence
SH Return       Loop and play music from top of current sequence (note: up arrow in clock)
N               Turn note to tie/normal
SH N            All marked notes turned to normal
CBM N           All marked notes turned to tie
G               Gate on (GAT in sequence)
SH G            Gate off (gat in sequence)

When entering notes in the sequencer you have 
2 octaves present at all times:
------------------------------
    1 2  4 5 6  8 9  + - 
CTRL Q WE R T YU I OP @ * UpArrow

Hold down SHIFT to get tie/glide/attack notes.


TRACKER KEYBOARD COMMANDS:
-------------------------------------------------------------------------------
>               Increase transpose values or sequence values.
<               Increase transpose values or sequence values.
InstDel         Delete a track line
SH InstDel      Insert a track line
Return          Set loop mark for current channel
SH Return       Set stop mark for current channel
SH 123          Swap tracks (including all sub songs - music must be off)


SOUND/INSTRUMENT EDITOR KEYBOARD COMMANDS:
-------------------------------------------------------------------------------
N               Name sound/instrument (return to exit)
+/-             Select sound
SH +/-          Select sound with focus on displaying their programs
SH A            Arpeggio program table
SH F            Filter program table
SH I            Initial volume and Filter channels/Filter speed table.
SH P            Pulse program table
SH S            Sound setup table
SH T            Tempo program table
SH V            Vibrato program table
SH W            Waveform program table
M               Mark sound
SH M            Copy sound
>/<             Select arpeggio number with focus on displaying it's arpeggio data.

Return          Put current program line into sound setup
                Only for waveform, pulse, filter and vibrato.
                (Return in tempo table will set default tempo for this song.)
SH Return       Delete program from sound setup.
                Only for waveform, pulse, filter and vibrato.
,/.             Jump 4 lines up/down
ClrHome         Go to current sound's program line (if there's one).
                (For arpeggio it will display current arpeggio at top).
SH ClrHome      Go to top of program line table
InstDel         Delete a program line. (not for sound setup table)
SH InstDel      Insert a program line. (not for sound setup table)


LOAD MENUE COMMANDS:
-------------------------------------------------------------------------------
SPACE          Read a new directory into memory
SH SPACE       Go to DOS command screen
*              Display files A-Z
SH *           Display files Z-A
A-Z            Set display path
CTRL 1-0       Select disk drive 11,12,13,14,15,16,17,8,9 and 10.
Crsr keys      Select music
Return         Load music
,/.            Jump 8 files up/down
ClrHome        Top of directory
SH ClrHome     Bottom of directory
RunStop        Exit


SAVE/DUMP COMMANDS:
-------------------------------------------------------------------------------
RunStop        Exit
Return         Save/Dump music
InstDel        Delete text


DOS COMMANDS:
-------------------------------------------------------------------------------
The dos command screen can be used to handle files and directories.
Anything you do here is at your own risk. Know what you are doing.
I only reccomend to use the commands listed, it is possible to use other commands.

Keyboard:
CRSR            Move cursror around.
CLRHOME         Go to start of commandline.
SH CLRHOME      Clear commandline.
RETURN          Send disk command.
RunStop         Exit to load menue.


Wildcards are ? and *

The following commands works on all drives:
$                   - Display dir
$a*                 - Display files starting with the letter 'a'
$??a*               - Display files where the 3rd letter is 'a'
S0:FILENAME         - Scratchfile
R0:NEWNAME=OLDNAME  - Rename file
N0:DISKNAME,ID      - Format disk (ID must be 2 letters for 1541 format)
V                   - Validate disk
I                   - Initialize drive
UI                  - Reset drive (returns dos version number)


The following commands works on CMD drives:
MD:DIRNAME          - Make dir
RD:DIRNAME          - Remove dir
CD:DIRNAME          - Go to dir
CD:/                - Go down one dir level


The following commands works on the IDE64:
MD:DIRNAME          - Make dir
RD:DIRNAME          - Remove dir
CD:DIRNAME          - Change dir
/DIRNAME            - Change dir
/                   - Go down one dir level + autodisplay dir
CD:..               - Go down one dir level
/..                 - Go down one dir level (root dir?) + autodisplay dir
T-RA                - Display date and time

And if you got a sd2iec or similar iec device you can use most of
the commands mentioned above.



PC/EMULATOR USERS:
-------------------------------------------------------------------------------
Restore         Page Up
CTRL            Tab Key
RunStop         CapsLock / Escape
Return          Enter
CBM             CTRL
<-               (The key above the Tab key)
=               ' (They key above right shift and to the left of the enter key)
/               /_ (Can also be the underscore key)
?               ?_ (Can be the shift + underscore key)
CRSR            Arrow keys
*               ^}
ClrHome         Home
A#?             Insert
h-?             Delete

