I used a product to regenerate the rubber keypad of remote controls to repair the keyboard flat cable of a Home Computer MSX.

I have used this product many times for my work of Retro Computer restoration but never to regenerate the rubber keypad of remote controls :D

Gallery of the repair:

Jean-François DEL NERO (who’s behind the HxC SD Floppy Emulator) recently has released a version of the HxC emulator firmware that is compatible with the STM32 chip used in the Gotek floppy emulators.

This means that the great functionality of the HxC SD emulator is now available on cheaper and more widely available hardware.

The bootloader to convert the Gotek floppy drive in HxC compatible must be purchased on the website HXC 2001 by sending an email to Jean-François DEL NERO. The price of the bootloader is one-off 10 Euro per Gotek that you want to update. Future updates of the software are free and can be made from a USB stick

The HXC Usb (Gotek) firmware supports:

Release notes Firmware USB HxCFloppyEmulator v3.0.8.1a

• Last selected image save issue corrected.

Release notes Firmware USB HxCFloppyEmulator v3.0.8.0a

• “Autoboot”/ File selector mode :
  • Fast backward/forward mode : Keep the button pressed to speed up the image change.
  • Press both buttons in the same time to jump the autoboot/file selector image.
• Indexed mode :
  • Fast backward/forward mode : Keep the button pressed to speed up the image change.
  • Press both buttons in the same time to jump the DSKA0000 image.
• Up to 1000 indexed images (DSKA0000-DSKA0999).

Download: USB Stick STM32 (Gotek) HxC Firmware v3.0.8.1a (1186)

source: hxc2001.com

Commodore 64C (ASSY 250469) Repair (1 of 12)

Defect:

• Black Screen.

Replaced parts:

• 1 x MOS 6526 (U1)

Gallery of the repair:

Commodore 64C (ASSY 250469) Repair (2 of 12)

Defect:

• Black Screen.

Replaced parts:

• 2 x TMS 4464 (U10/U11)

Gallery of the repair:

Commodore 64C (ASSY 250469) Repair (3 of 12)

Defect:

• Black Screen.
• Keyboard Dead.

Replaced parts:

• 2 x TMS 4464 (U10/U11)
• 1 x MOS 6526 (U1)

Gallery of the repair:

Read more…

The motherboard conditions are not good, very badly. All capacitors have released acid, some are gone and the same for other components like the transistor Q233 2N3904 SMD amplifying for the video signal BLUE RGB. The Decoder U12 CXA1145 Sony has the pins eaten by the acid of the capacitors.

Poor Amiga …

Work to do:

• Solder resistance from E232R that is disconnected because the acid of the capacitors has leaked and corroded..
• Solder the transistor Q233 that is disconnected because the acid of the capacitors has leaked and corroded.
• Rebuilding a dozen pf pcb track between the IC U12 and the rest of the PCB and rebuilding also the through holes of the PCB.
• Replacing electrolytic capacitors, probably due to the state of the pitches i don’t use SMD capacitors.
• Replacing the male Harddisk connector some legs are broken at the base because the acid of the capacitors has leaked and corroded.

Gallery of the repair & cleaning:

1234►

I start to saying that this type of repair should NOT be made, are not good although the repair can succeed, these damaged motherboards are good for spare parts.

It took me 10 hours to repair and if i ask 15,00 euro per hour like a housekeeper, would be 150,00 euro excluding components and cleaning case … but who pays 150,00+ euro ? no one in the world. :-D

This is one of the reasons because do not exist anymore electronic repairs or there are very few people can do it, nobody is willing to pay.

Works that have been made:

Foreword almost all pcb pads are leaked of the acid, although i have cleaned more times so as not to heat the electrolyte liquid that is worsening the situation, unfortunately the pcb pad could not resist to a new solder and they are broken.

• Soldered the E232R resistor, it’s no a good soldering because the pad are in a badly state but working.
• Soldered a transistors Q233 (2N3904) not SMD, the pitches are gone when i have tried to solder the SMD version.
• Rebuilt 10 x connections doing a horrible jumpers in bizarre places.
• Replaced the electrolytic capacitors.
• Replaced the male connector for the Harddisk.

It’s a shit … but it works!

Commodore Amiga 600 Gallery (Before & After):

Yet another Commodore 64 (USA-NTSC) repaired.

Defect:

• Garbage screen / Black screen.

Repair:

• Replaced 1 x PLA 906114
• Replaced 1 x MOS 7708 (74LS257)

Note:

• The first time the Garbage Screen was in Black & White and then after replacing the PLA 906114 a new Garbage Screen is back with some colors :-D (see photo)

Gallery of the repair:

Texas Instruments TI-99/4A Repair (#1)

Defect:

• Wave/Raster Lines.

Replaced parts:

• 1 x Variable Inductor 2 -> 4.5 μH (L100).

Gallery of repair:

Texas Instruments TI-99/4A Repair (#2)

I should point out that someone has already tried to repair, without success.

Defects:

• Black Screen (no raster, no sync) short circuit between 12v and 5v . . . and then . . .
• Wave/Raster Lines.
• Blue Screen with tiny Vertical lines and deafening sound.
• Garbage Screen.

Short Circuit Note:

• The short circuit was due to a malfunction of the IC: TIM9904ANL (U601)

Replaced parts:

• 1 x Variable Inductor 2 -> 4.5 μH (L100).
• 1 x TIM9904ANL (U601)
• 2 x MCM 6810P RAM 128×8 (U608 – U609)
• 1 x 74LS245 (U614)
• 1 x TMS9929 (U100)

Gallery of the repair:

Commodore PET 2001 Chiclet (1978) Fixed.

Defect:

• Garbage screen.

Repair:

The problem of this computer was caused by the oxide on all pins of the RAM and inside of the sockets as you can see from the photos.

To clean the pins of the IC i always use the same way, gently with a rasp nail on the ic pins and then spray a bit of air, see photo.

For cleaning the socket i scraping with a fine tip gently the contact inside the socket.

I have tested all with the ROM/RAM board and simulating the various BASIC and configurations of RAM and loaded some software, including my demo with the PET MicroSD by Dave Curran (Tynemouth Software)

Everything worked perfectly.

As you can see from the photos i have now a complete workstation for repair PET 2001 out of the box, avoiding to have on the table the computer that takes a lot of space.

Gallery of the repair: