I received this console to made a repair and a video chip upgrade.

The repair:

The failure appeared as a malfunction of the Joystick inserted in port #1 of the console. This problem is absolutely not new to this console.

The failure is due to the 74LS541 IC which, in addition to being uncommon (it is rarely used), is very sensitive to electrostatic electricity, consequently if you try to connect the joystick with the console turned on, the probability that it will fail is very high.

I preferred to replace with a socket for both IC, one for each joystick port, because the probability of a future failure remains very high.

Video Chip Upgrade:

I would like to point out that this CBS ColecoVision model does not have native RGB video output but only RF.

It was possible to do the Composite Video mod but since in recent months the good Troy Schrapel has released on github the Pico9918 project that completely replaces the TMS9918A video chip and the Video RAM with a very low cost i decided to do the replacement.

This Video Chip are used in many consoles and computers including the CBS ColecoVision.

The Pico9918 can be configured using a different firmware to output in VGA or via SCART RGB.

I obviously chose the RGB SCART output, the installation is quite simple, you have to unsolder the TMS9918A, insert a socket and at this point you can insert the pre-programmed Pico9918 and connect the R-G-B-GND-SYNC (H/V) signals, optional you can completely remove the PCB with the RF modulator.

The wires that you see soldered directly on the ColecoVision motherboard are for the AUDIO output (purple wire) and for the 5v (orange wire) the 5v are for the RGB switching of the TV.

The connections inside the scart connector are as follows: the 5v go to pin 8 and then via a 150ohm resistor to pin 16.

Also as you can always see from the photos i put some adhesive tape on the metal cover at the height of the Pico9918, i did it only for my personal paranoia, the metal does not touch the Pico9918 but better to be safe :-D

Gallery of the repair and upgrade:

12►

source: github.com/visrealm/pico9918

Unfortunately, as often happens, the mechanics of the ATARI XC11 cassette recorder also suffer from old age problems. The cap/block of the belt drive pulley broke and consequently, being under pressure with a spring, it popped off.

I fixed the cap on the small plastic pin of the pulley with cyanoacrylate glue, it could work forever or only for a short time, only time will tell.

Gallery of the repair:

I wanted to upgrade another Philips Videopac G7000 console and adding everything i wanted to do many years ago when i only added the RGB output instead of the RF one.

While i was doing the work of modifying the console i realized that something was wrong with the games and the RGB output, some games were missing the background color or the color was faded, other times the colors are wrong, but this defect was not present with all games and therefore it was not a wiring problem (colors are not swapped likes a problem with the R-G-B wiring).

I had never realized it and probably other people have never realized it either, because it does not happen with all the games but thanks to the Flash Multicart by Andrea Ottaviani i was able to try all the software released for the G7000 and confirm that something was not working correctly.

The problem is due to the type of RGB mod, i had taken the one from the gamesx.com site as good, that is the one that has been available from about fifteen years and that almost everyone has installed but there is another mod that is completely different and above all uses a particular pin of the Intel 8048 CPU (pin 39 [T1]).

Hesitantly i wanted to try this modification and it is actually all true, it works, now the RGB mod is perfect as for the Videopac G7200 (native with RGB output) and G7400 (Native RGB by adding the components that are missing on the PCB)

Later i discovered that this RGB mod was not born like this by chance, the scheme was designed taking inspiration from the original schematic of the G7200/G7400 where this particular CPU pin is used.

Below is the list of all the modifications and enhancements that have been made:

• RGB Mod 100% Working with a extra pin from CPU (No more missing background or colors via RGB on G7000)
• External RGB DIN Hirschmann Connector.
• Power external Switch with Power-On Light.
• Power external Connector.
• Two Joystick D-SUB external Connector.
• Replaced the original PSU with a Mean Well EPS-15-5.
• RF modulator removed.
• Simple Composite Video signal amplification circuit.
• Separate composite Video and Audio output via external RCA connectors.

Gallery of the work done:

123►

…and now some links:

https://forum.system-cfg.com/viewtopic.php?f=18&t=10673
https://gamesx.com/wiki/doku.php?id=av:g7000_av
https://darius-saturn.com/forum/viewtopic.php?t=8342
https://www.pimparts.fr

First of all i have to thank Ralf Schmitz for this gift. (Grazie Ralf).

Short description taken directly from Wikipedia of the Saba Videoplay console (Fairchild Channel F):

The Fairchild Channel F, short for “Channel Fun”, is a video game console, the first to be based on a microprocessor and to use ROM cartridges (branded ‘Videocarts’) instead of having games built-in. It was released by Fairchild Camera and Instrument in November 1976 across North America at a retail price of US$169.95 (equivalent to $910 in 2023)

The console come in a fair state of preservation but still had the following problems:

• Broken reset button.
• Both joysticks did not work properly.
• A small part of the corner of the PCB of the power switch side was broken.
• Rough repair with adhesive tape of the cable of both joysticks.

The repair was quite simple but boring, fixing the joystick cable was not exactly fun, i had to cut the cable because one or more wires inside are broken, i also had to invent a cable gland for a missing joystick and drill a cable gland with the broken cable right inside to then insert the cutted cable and solder the wires inside the joystick. (see photo)

The reset button was enough to glue it. (see photo)

I polished the console case that had the classic matte and dry black color of 70s plastics with linseed oil, a little is enough on a makeup remover PAD or a cotton rag, the result is amazing.

For completeness i also installed the e5frog composite video modification that works well, i only had to bring an auxiliary ground (although the ground of the negative power supply is already connected) from the PCB to the metal body (see photo) because it gave me video noise, now it’s perfect.

Below the photo gallery:

123►

Philips Monitor (Black) VG0060-80 Power Stage Repair, the Monitor turned off unexpectedly without any suspicious noise.

This power stage is practically identical to other monitor models, for example: Philips CM8833 and Commodore 1084, but surely there will be others that mount the same power stage.

Repair:

After removing the PCB of the power stage i took the opportunity to replace also the power switch that no longer worked properly i also replaced the exploded fuse but obviously nothing worked.

The fault was due to the TS132 transistor completely short-circuited, the diagram says that a BU806 is installed but instead a 2SC3795B is installed.

Replaced, still nothing works, i tried with the tester but i don’t find any voltage, even the 300v +/- on the capacitor C112 at this point in addition to the diode bridge (D107/D108/D109/D110) there was only the 47 Ohm 7W resistor R103 to try and in fact it was interrupted, i replaced it with a 5W one, i didn’t have a 7W one in the lab.

I used the old trick of the 100W bulb in series, in my case instead of the fuse to avoid destroying other components.

Everything worked perfectly, the bulb turned on for a minimum amount of time and then turned off and the output voltages of the power stage are all present (125v/15.8v/25.5v).

Gallery:

Download: Philips VS0060-80/CM8833/1084 Schematics (354)

I purchased the Texas Instruments Grillo Parlante Più (Super Speak & Spell) for a few euros and fully aware that the contact plates for the batteries due to an acid leak has been destroyed (see photo).

After testing it if actually still worked, i did a good cleaning of the battery compartment, body and display.

I replaced the contact plates for the batteries with similar ones recovered from an old dead and defunct cassette recorder.

The final result is perfect, it looks like the original, even better because i put the battery negative spring in the correct side, the original has the springs all on one side, both for the positive and negative of the battery.

Gallery of work done:

Video:

First of all, i thank my friend who gave me his Sega SC-3000 found in the attic.

After a thorough cleaning of the cartridge connector, keyboard contacts and general cleaning of the internal/external case, the computer started working perfectly again.

Gallery:

First of all, i thank my friend Gerben for giving me the monitor.

This is a Black and White monitor but for some reason a thin transparent film has been applied to the front of the cinescope to simulate the tonality of an amber cathode ray tube, furthermore the APF logo placed on the front of the monitor to the right of the power light is masked.

The TVM-10 APF Monitor is approximately 43 years old and was used with the Computer APF Imagination Machine I/II.

The Monitor had several functioning problems, below is the description of the work that has been done.

• Removing the colored film.
• Replacement of all electrolytic capacitors.
• Replacement of a ceramic capacitor.
• Horizontal synchronism calibration (H-HOLD) by delicately removing the wax that was melted inside the variable inductor.
• Installation of a 1uf polyester capacitor in parallel with the 1.5uf one present for width adjustment horizontal (H-WIDTH) of the image, unfortunately the ferrite core inserted into the variable inductor for manual adjustment is blocked, probably with glue, forcing is not a good idea.
• Check of the Diodes.
• Calibration using the trimmer placed on the front of the PCB of the monitor for the power supply voltage which must be 12v.
• Geometry adjustment.
• General cleaning.

Only one geometry problem remains; the image on the top left side of the CRT tends to bend slightly for about 1cm and the left side of the image is slighty rounded, problem surely attributable to some polyester capacitor or resistance that has lost the capacity/value of the time.

Needless to say i checked almost all the polyester capacitors and resistors in the horizontal section and didn’t find nothing scandalous.

The photo gallery contains all the photos i made during the repair, i take this opportunity to thank a user of the plcforum who gave me tips on how to proceed with the repair.

Gallery of the repair:

123►

Apple ][ EuroPlus Repair.

Defects:

• Black screen.
• Power light off.
• Keyboard does not work.

Repair:

About the black screen it was enough to press all the IC in their seat, i have removed some and cleaned the IC's socket and the IC's pins.

The Power light off, the 5v micro bulb was faulty, replaced.

The keyboard had several problems;

The keyboard connector (socket) located on the computer motherboard side was faulty and consequently are missing the -12v for the keyboard encoder PCB.

The 3 TTL chips had been replaced on the keyboard encoder PCB but 2 x 74LS04 are erroneously soldered instead of 2 x 74LS00, the third TTL was correct but not working. Replaced all.

Now everything works reasonably well, unfortunately the bad keyboard has some problems, the internal slats are warped and tend out of their seat, as a result some keys do not work correctly.

I have tried to fix and clean, but the situation hasn't improved much.

Gallery of the repair:

Texas Instruments PHA 2037 Connector FIX

Defect:

• Black Screen but sounds works.

Replaced parts:

• 1 x 6 PIN DIN Male.

Gallery: